Important safety information

Bluedio Hurricane Turbine User Manual Pdf 2 8
Bluedio Hurricane Turbine User Manual Pdf File
Bluedio Headphones Hurricane Turbine Manual

Do not listen at high volume levels for long periods of time to prevent hearing damage.
Do not use the product if there is any potential danger.
Do not turn the volume too high to hear sounds around you, turn down the volume if you feel a tinnitus or the volume is too high.
Do not use the product in an environment that requires your special attention (e.g. in traffic).
Keep the product, accessories and packaging parts out of reach of children, to prevent accidents and choking hazards.
Always keep the product dry to avoid corrosion.
Do not use the product if you feelobvious discomfort, irritationor haveotheradverse reactions.
Do not expose the product to extreme temperatures below -15℃ (5℉) or above 55℃ (131℉), to maintain the lifespan of headset or battery.

Delivery includes

T2S Bluetooth headset

Jul 22, 2017 Bluedio T4 (Turbine) Active Noise Cancelling Over-ear Bluetooth Headphones ANC Technology T4's Active Noise Cancelling technology cuts off.

For this reason, Bluedio keep hard working on 3 years of R&D and testing, manage to customize a wireless headphone with unrivaled timbre, adapted to a variety of rugged circumstances and highly cost-effective. Thoughtful design, unexpected superior sound, make luxury become reasonable, this is Hurricane H(Shooting Brake) Bluetooth 4.1 headphone. Recent search for: invensys d 78559 gosheim gaggenau ah 250 191 nec pabx ip1e-8ksu-a1 manual neff h7860n1gb 01 karcher hds 1210 equilibradora facom u47 daikin fvy45av1 uso vizyon vz-1030 cax aeg lavamat 47290 update candy alise 879 wash baxi roca bios miele t471c casadei tc110 whirlpool fxrm6 four ariston ab grunding gemsy rxm 77 a uso. For this reason, Bluedio keep hard working on 3 years of R&D and testing, manage to customize a wireless headphone with unrivaled timbre, adapted to a variety of rugged circumstances and highly cost-effective. Thoughtful design, unexpected superior sound, make luxury become reasonable, this is Hurricane H(Shooting Brake) Bluetooth 4.1 headphone.

USB charging cable

Audio cable

User manual

Headset Overview

Charging and battery

Only use charging cable supplied by Bluedio, or may cause damage to the headset.

Warning

The DC voltage should be 5V and current should exceed 400mA.

Charging

The headset built-in battery is rechargeable and non-detachable. Do not replace the battery.

Switch off the headset before charging.
Connect the smaller plug of the charging cable to the USB socket of the headset; connect the other plug to the USB socket of your computer or other charging device; the LED lights up red and the headset is being charged.
When the headset is fully charged (about 1.5~2hrs), the LED lights up blue or LED goes out.

Pairing mode

Keep the MF button pressed until the LED lights up blue.

Reconnection mode

Keep the MF button pressed until the LED flashes blue.

Switching the headset off

Keep the MF Button pressed until the LED flashes blue then goes off.

Programming Digital Out1 Sel, parameter 380 will be ignored when TorqProve Cnfg is set to “Enable.”Figure 6 - Typical 24V Torque Proving ConfigurationLifting/Torque Proving Application ProgrammingThe PowerFlex 700 lifting application is mainly influenced by parameters 600 through 611 in the Torque Proving group of the Application file.and theparagraphs that follow describe programming.Figure 7 - Torque Proving Flow DiagramTorque ProvingWhen the drive receives a start command to begin a lifting operation, the following actions occur:1. This provides the mechanical brake with voltage, causing the brake to release. Any interruption of power to the contactor will set the mechanical brake. The drive first performs a transistor diagnostic test to check for phase-to-phase and phase-to-ground shorts. A failure status from either of these tests will result in a drive fault and the brake relay will NOT be energized (brake remains set).24 25 26 27 28 29 30 31 32Run Fwd Run Rev Clear Faults Float/Micro Fast Stop Enable12 13115V ACBrakeContactorBrake SetNormally Open= Brake SetTorqueProve InitiatedBrakeReleasedFloatInitiatedBrakeSetBrakeSlip TestRunCommandRunCommand ReleasedDrive RunningRun can be initiated anytimeAll times between Drive Actions are programmable and can be made very small(i.e. Powerflex 700 vector control user manual free.

Pairing the headset with your mobile phone

Keep the distance between the headset and your mobile phone (or other Bluetooth device) within 1 meter. The closer, the better.
Keep the MF button pressed until the LED lights up blue. The headset is in pairing mode.
Switch on the Bluetooth function of your mobile phone, on which start a search for Bluetooth devices.
Select “T2S” from the found Bluetooth devices to establish a Bluetooth connection to the headset. If necessary, enter the default PIN code “0000”.
Once the headset is paired with the mobile phone, the LED flashes blue.

Attention: If pairing is not successful within 60 seconds, the LED goes off and the Bluetooth pairing ends. Repeat the pairing procedure.

Disconnecting the headset with your mobile phone

Switch the headset off.
Or switch off the Bluetooth function of your mobile phone.
Or take the headset from your mobile phone 20m (60ft) away or even farther.

Reconnecting the paired headset to your mobile phone

Keep the distance between the headset and your mobile phone (or other Bluetooth device) within 1 meter. The closer, the better.
Keep the MF button pressed until the LED flashes blue. The headset is in reconnection mode.
Switch on the Bluetooth function of your mobile phone. The headset will automatically reconnect to it.

Answering a call

When there comes a call, the LED flashes blue; press the MF button once, or use your mobile phone to answer it.

Ending a call

Press the MF button once. Or use your mobile phone to end it.

Rejecting a call

After hearing a beep, keep the MF button pressed for around 2 seconds or use your mobile phone to reject it.

Call waiting (need to be supported by your mobile phone)

When you are on call 1, there comes call 2; to answer call 2 and keep call 1: keep the MF button pressed for around 2 seconds.

When call 2 ends, to switch back to call 1: keep the MF button pressed for around 2 seconds

Redialing the last call

Press the MF button twice

Voice dialing (need to be supported by your mobile phone)

Keep the MF button pressed for around 2 seconds

Voice prompt selection

Switch the headset on, press the MF button and Vol- button once at the same time to select English/Chinese/French/Spanish.

Muting

When you are on call, keep the Vol- button pressed to mute the Microphone; keep the Vol+ button pressed to cancel the muting.

Audio sharing

Connect the headset with your mobile phone via Bluetooth, then connect the headset to another headphone via audio cable.

Being a Bluetooth receiver

Connect the headset with your mobile phone via Bluetooth, then connect the headset to amplifier via audio cable.

Line-in connection

Connect the headset with your mobile phone via audio cable. (In this mode, the headset cannot be used for communication)

EQ adjustment (only in Bluetooth mode)

When the headset is playing music, press the Vol+ button and Vol- button once at the same time.

Track play/

Bluedio Hurricane Turbine User Manual Pdf